Adlink LEC-iMX6 Manuale Utente

Advance Technologies. Automate the World.LEC‐iMX6(Computer‐on‐Module)Technical ReferenceP/N50‐1Z167‐1000Rev1.0

6 Overview1.4.3 Power SpecificationsTable 1-4 provides the power requirements for this module.Operating configurations:  In-rush operating configurat

Overview 7LEC-iMX61.5 Getting StartedThis section describes how to configure the boot select jumpers on the LEC-BASE baseboardand how to configure U-

8 Overview1.5.2 Verify U-Boot ConfigurationTo ensure U-Boot will run a Linux image from the corresponding boot device, perform the follow-ing steps.1.

Overview 9LEC-iMX66. To run Linux from USB by default, edit bootcmd using: edit bootcmd run boot_usb save Note: You need to enter “save” after mak

10 Hardware2 Hardware2.1 CPUThe LEC-iMX6 product family offers four models of the Freescale™ i.MX6 CPU: the i.MX 6Solo(1x Core), the i.MX 6Dual (2x Co

Interfaces 11LEC-iMX63 InterfacesThis section provides descriptions of the interfaces and signals within the SMARC P-S (Pri-mary-Secondary) connector

12 Interfaces3.3 HDMI (High-Definition Multimedia Interface)The HDMI port utilizes the following HDMI pins on the SMARC interface: 1 Clock pair (P101

Interfaces 13LEC-iMX63.8 USB 2.0 PortsThe LEC-iMX6 provides two host USB ports and one OTG port. The two host ports are providedfrom a 4-port USB HUB

14 Interfaces3.12 Serial (UART)The LEC-iMX6 provides four serial interfaces: Two ports are high-speed, 4-wire ports (with TX/RX and RTS#/CTS#), and tw

Interfaces 15LEC-iMX63.17 eMMC InterfaceThe LEC-iMX6 provides one eMMC NAND Flash memory chip with up to 64GB storage capac-ity, accessible from the

iiDisclaimerInformation in this document is provided in connection with ADLINK products. No license,express or implied, by estoppel or otherwise, to a

16 Interface Signals4 Interface Signals4.1 SMARC InterfaceTable 4-1 provides the pin signals for the SMARC P-S connector. Refer to the SMARC specifica

Interface Signals 17LEC-iMX6P42 SDIO_D3 S43 Not connectedP43 SPI0_CS0# S44 Not connectedP44 SPI0_CK S45 Not connectedP45 SPI0_DIN S46 Not connectedP4

18 Interface SignalsP92 HDMI_D2+ S93 LCD_D0P93 HDMI_D2- S94 LCD_D1P94 GND S95 LCD_D2P95 HDMI_D1+ S96 LCD_D3P96 HDMI_D1- S97 LCD_D4P97 GND S98 LCD_D5P9

Interface Signals 19LEC-iMX64.2 Debug (DB40)Table 4-2 lists the pin signals of the CN2 connector, which provides 40 pins, 1 row, consecutivesequence

20 Power and System ManagementNOTE: The gray table cells denote ground.5 Power and System Management5.1 SEMA UtilityUnder the management of the BMC ch

21LEC-iMX6Appendix A Technical Support ADLINK Technology, Inc. provides a number of methods for contacting Technical Support listedin Table A-1 bel

22Table A-1: Technical Support Contact Information (Continued)ADLINK Technology, Inc. (French Liaison Office) Address: 6 allée de Londres, Immeubl

23LEC-iMX6Table A-1: Technical Support Contact Information (Continued)ADLINK Technology, Inc. (Israeli Liaison Office) Address: 27 Maskit St., Co

24

iiiLEC-iMX6Table of Contents1 Overview ...

iv5 Power and System Management ... 205.1 SEMA Utility ...

Overview 1LEC-iMX61 OverviewThis initial manual version presents a general overview of the LEC-iMX6. After reviewing thisdocument you should understa

2 Overview1.2 Major Components (ICs)Table 1-1 lists the major integrated circuits on the LEC-iMX6, including a brief description ofeach IC. Figure 1-2

Overview 3LEC-iMX6Figure 1-3: Component Locations (Bottom Side)1.3 Connectors, LEDs, and SwitchesTable 1-2 describes the connectors, LEDs, and switch

4 OverviewFigure 1-4: Connector, LED, and Switch Locations (Top Side)1.4 Specifications1.4.1 Physical SpecificationsTable 1-3 lists the physical dimen

Overview 5LEC-iMX61.4.2 Mechanical SpecificationsFigure 1-5: Mechanical Dimensions (Top Side)NOTE: All dimensions are given in millimeters. LEC-iMX6_