Adlink ETX-BT Manuale Utente

ETX-BT User’s Manual Manual Revision: 1.01 Revision Date: May 7, 2015 Part Number: 50-1J059-1010

Page 10 2.4 Ethernet X Type: Intel® i211 (MAC/PHY) Ethernet controller X Interface: 10/100 Mbps on ETX signal connector (build option for 1000/100

Page 11 2.7 SEMA Board Controller X Type: BMC uPD78F0763GB X Functions o Power Features  AT mode control  Emergency shutdown  Power status

Page 12 2.8 Power X Standard Input: ATX = 5V±5% / 5Vsb ±5% or AT = 5V±5% X Management: ACPI 4.0 compliant, Smart Battery support X Power States:

Page 13 3 Functional Diagram FPC

Page 14 4 Mechanical Dimensions Top View Side ViewAll tolerances ± 0.05 mmOther tolerances ± 0.2 mm

Page 15 5 Pinouts and Signal Descriptions Crossed out signals are not supported. 3V (3.3 V ±5%) is generated on board. Pins may be used to power dev

Page 16 X1 Signal Descriptions Pin Signal Description Type PU/PD Comment 1 GND Ground PWR - - 2 GND Ground PWR - - 3 PCICLK3 PCI Clock Slo

Page 17 Pin Signal Description Type PU/PD Comment 51 5VCC Power +5V PWR 52 5VCC Power +5V PWR 53 PAR PCI Bus Parity IO-3,3

Page 18 5.2 X2: ISA Pin Signal Pin Signal Pin Signal Pin Signal 1 GND 2 GND 51 VCC 52 VCC 3 SD14 4 SD15 53 SA6 54 IRQ5 5 SD13 6 MASTE

Page 19 X2 Signal Descriptions Pin Signal Description Type PU/PD Comment 1 GND Ground PWR - - 2 GND Ground PWR - - 3 SD14 ISA Data Bus I

Page 2 Revision History Revision Description Date By 1.00 Initial release 2015-03-18 JC 1.01 Correct SPI Boot Device Switch settings 2015-05-0

Page 20 Pin Signal Description Type PU/PD Comment 51 5VCC Power +5V PWR - - 52 5VCC Power +5V PWR - - 53 SA6 ISA Address Bus O-5 PU 4k7

Page 21 5.3 X3: LVDS, Serial, Parallel, KB, MS Pin Signal Pin Signal Pin Signal Pin Signal 1 GND 2 GND 51 LPT/FLPY# 52 RESERVED 3 R 4 B 5

Page 22 X3 Signal Descriptions Pin Signal Description Type PU/PD Comment 1 GND Ground PWR - - 2 GND Ground PWR - - 3 R Analog Video Out R

Page 23 Pin Signal Description Type PU/PD Comment 51 LPT | FLPY# LPT / Floppy Interface Select NC - - 52 RESERVED NC - 53 5VCC Power

Page 24 5.4 X4: IDE 1, IDE 2, Ethernet, Miscellaneous Pin Signal Pin Signal Pin Signal Pin Signal 1 GND 2 GND 51 SIDE_IOW# 52 PIDE_IOR# 3 5V

Page 25 X4 Signal Descriptions Pin Signal Description Type PU/PD Comment 1 GND Ground PWR - - 2 GND Ground PWR - - 3 5V_SB Supply of inter

Page 26 Pin Signal Description Type PU/PD Comment 51 S_IOW# Secondary IDE IO Write O-3,3 - - 52 P_IOR# Primary IDE IO Read O-3,3 - - 53

Page 27 6 Module Interfaces This chapter describes connectors with pin outs, LEDs and switches that are used on the module but which interfaces are n

Page 28 Solder Side PCI Voltage Selection SW3 SPI BootSelection SW1

Page 29 6.2 40-pin Multipurpose Connector FPC Connector Type: FCI 59GF Flex 10042867 Pin Orientation: Pin Definitions (on ETX module) Pin Interface

Page 3 Preface Copyright 2015 ADLINK Technology, Inc. This document contains proprietary information protected by copyright. All rights are reserved

Page 30 ETX-BT and the DB40 Module connected 6.3 Status LEDs To facilitate easier maintenance, status LED’s are mounted on the board. LED1

Page 31 6.4 XDP Debug Header Connector Type: Molex 26-pin 52435-2671 The debug port is a connection into a target-system environment that provides

Page 32 6.5 DP Connector Connector Type: Wurth WE 6871 2214 522 The DP connector brings out DDI1 port of the Intel® Atom™ SoC as either DP or HDMI/

Page 33 For HDMI/DVI output, pins 20, 21, 22 should not be used but power should be sourced from 5V (5VS0) rail on the carrier 6.6 Fan Connector Con

Page 34 6.7 GbE Connector Normal support for 100/10 Mbps LAN is through the X4 connector. There is a build option to disconnect these signals and ins

Page 35 6.8 SW1: SPI Boot Device Selection The ETX-BT supports a form of fail-safe BIOS. In the case that the primary BIOS is corrupted and the BIOS

Page 36 3. The BIOS prompt screen will display a confirmation that BIOS defaults have been reset and request that you reboot the system.

Page 37 6.10 SW4: PCI Interrupt Routing Select Standard PCI routing is compliant with ETX specification rev 3.02, as below In some cases (e.g. rea

Page 38 7 SEMA (Smart Embedded Management Agent) The onboard microcontroller (BMC) implements power sequencing and Smart Embedded Management Agent (S

Page 39 7.1 Board Specific SEMA Functions 7.1.1 Voltages The BMC of the ETX-BT implements a voltage monitor and samples several onboard voltages. The

Page 4 Table of Contents Revision History...2 Preface ...

Page 40 7.1.3 BMC Status This register shows the status of BMC controlled signals on the ETX-BT. Status Bit Signal 0 WDT_OUT 1 LVDS_VDDEN 2 LVDS_BK

Page 41 7.1.4 Exception Codes In case of an error, the BMC drives a blinking code on the blue Status LED (LED1). The same error code is also reported

Page 42 7.1.5 BMC Flags The BMC Flags register returns the last detected Exception Code since power-up and shows the BIOS in use and the power mode.

Page 43 8 System Resources 8.1 System Memory Map Address Range (decimal) Address Range (hex) Size Description Start 128KB below 1MB 000E0000h-000

Page 44 8.3 Interrupt Request (IRQ) Lines 8.3.1 PIC Mode IRQ# Typical Interrupt Resource Connected to Pin Available 0 Counter 0 N/A No 1 Keyboa

Page 45 8.3.2 APIC Mode IRQ# Typical Interrupt Resource Connected to Pin Available 0 System timer N/A No 1 Standard PS/2 Keyboard N/A No 2 N/

Page 46 8.4 PCI Configuration Space Map Bus Number Device Number Function Number Routing Description 00h 00h 00h N/A Soc Transaction Router

Page 47 8.5 PCI Interrupt Routing Map INT Line Intel I.G.D PCIe Root Port#1 PCIe Root Port#2 PCIe Root Port#3 PCIe Root Port#4 SD Host # 0 eMMC SD

Page 48 8.6 SMBus Address Table Address (hex) Function Device A0 DDR3 channel A DDR3 socket C0 eDP to LVDS NXP3460 49 GbE LAN i211 2E Super I/O W8

Page 49 9 BIOS Setup 9.1 Menu Structure This section presents the six primary menus of the BIOS Setup Utility. Use the following table as a quick ref

Page 5 6.8 SW1: SPI Boot Device Selection... 35 6.9 SW2: BIOS Setup

Page 50 9.2 Main The Main Menu provides read-only information about your system and also allows you to set the System Date and Time. Refer to the tab

Page 51 9.2.6 System Management 9.2.6.1 System Management > Board Information Board Information Info only SMC Firmware Read only Display SMC

Page 52 Feature Options Description V1.05 Read only Display actual voltage of the V1.05. VMEM Read only Display actual voltage of the VME

Page 53 9.2.6.6 System Management > Power Up Feature Options Description Power Up Info only Power Up watchdog Attention: F12 disables the

Page 54 9.2.7 System Date and Time Feature Options Description System Date Weekday, MM/DD/YYYY Requires the alpha-numeric entry of the day of

Page 55 9.3 Advanced This menu contains the settings for most of the user interfaces in the system. 9.3.1 CPU Feature Options Description CPU In

Page 56 Feature Options Description Enabled CPU DTS Disabled Enabled Enabled/Disable Digital Thermal Sensor. 9.3.2 Memory Feature Options

Page 57 Feature Options Description IGFX Boot Display Device CRT Select the video device which will be activated during POST.This has no effec

Page 58 9.3.5 USB Feature Options Description USB Info only USB Module Version Info only USB Devices Info only X drive, x keyboards, x mouse

Page 59 Feature Options Description USB Pre Port Control Enabled Disabled Control each of the USB ports (0~3). Enable: Enable USB per port; Dis

Page 6 9.3.6 Network... 59

Page 60 9.3.8 Super IO Feature Options Description Super IO Chip Info only W83627DHG Super IO Configuration Info only Serial Port 1 Configu

Page 61 9.3.9 ACPI and Power Management Feature Options Description ACPI and Power Management Info only Enable ACPI Auto Configuration Enable

Page 62 9.3.11.1 Serial Port Console > Console Redirection Settings Feature Options Description COM0/COM1 Console Redirection Settings Info o

Page 63 9.3.12 ACPI Thermal Feature Options Description Thermal Info only CPU Temperature Info only Critical Trip Point Disabled 85 C 95 C Th

Page 64 9.3.13.1 Miscellaneous > BIOS Security Configuration Feature Options Description BIOS Security Configuration Info only Global SMI Lo

Page 65 9.4 Security 9.4.1 Password Description Feature Options Description Administrator Password Enter password User Password Enter pass

Page 66 9.5 Boot 9.5.1 Boot Configuration Feature Options Description Boot Configuration Info only Setup Prompt Timeout 1 Number of seconds

Page 67 Feature Options Description Boot option filter UEFI and Legacy Legacy only UEFI only This option controls Legacy/UEFI ROMs priority. Op

Page 68 Safety Instructions Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain al

Page 69 Getting Service ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan Tel: +886-2-8226-

Page 7 1 Introduction 1.1 Description The ETX-BT is based on the latest Intel® Atom™ processor E3800 SoC series, adopting the latest 22nm process tec

Page 70 ADLINK Technology, Inc. (French Liaison Office) Address: 6 allée de Londres, Immeuble Ceylan 91940 Les Ulis, France Tel: +33 (0) 1 60 1

Page 8 2 Specifications 2.1 General X CPU: Single, dual or quad-core Intel® Atom™ or Celeron® processor • Atom™ E3845 1.91 GHz 542/792 (Turbo) 10

Page 9 2.2 Video X Graphics Core: Intel 7th generation (Gen 7) graphics and media encode/decode engine (not supported on Atom™ E3805 S